Exploded view of a push button enclosure with front operators, rear modules and cable entry.

Push Button Enclosures: Sizes, Hole Layouts and Selection

Choose push button enclosures by operator size, hole layout, usable depth and wiring space. See catalog sizes and what to send for custom cutouts.

Choose push button enclosures around the complete controls you plan to install, including the parts behind the cover. Match the mounting holes, check usable depth, and place the cable entries before you order. The finished assembly needs enough room to tighten terminals, route wires and open the lid for maintenance.

A box described as “three-hole, 22 mm” still leaves several questions unanswered: how far apart are the holes, what sits behind each one, and where will the cable enter?

Exploded view of a push button enclosure with front operators, rear modules and cable entry.

What sizes do push button enclosures come in?

Keep two sets of dimensions separate: the operator mounting format and the box dimensions. A 22 mm or 30 mm description refers to the operator format, not the height or width of the enclosure. Hammond’s 1435 range, for example, has versions with 22.5 mm and 30.5 mm openings.

Here are four catalog examples from its 22.5 mm range:

ModelOperator holesCatalog H × W × D, inchesApproximate H × W × D, mm
1435MA13.50 × 3.25 × 2.7589 × 83 × 70
1435MB25.75 × 3.25 × 2.75146 × 83 × 70
1435MC38.00 × 3.25 × 2.75203 × 83 × 70
1435MH69.50 × 6.25 × 3.00241 × 159 × 76

Metric values are converted and rounded to the nearest millimeter. These are examples from one steel enclosure range, not universal sizes or usable internal dimensions.

Push button enclosures with different hole counts and cover layouts.

When comparing features, check how the cover is held during wiring, how the box mounts to the machine, and whether cable entries are already provided. Record those details alongside the dimensions; they affect how you assemble and service the controls.

Start with complete operator part numbers

List every push button, indicator, selector switch and emergency-stop device. Include the mounting hardware and everything attached behind the panel. For a modular operator, the front head alone will not tell you how much room the assembly needs.

Your list should identify:

  • The operator model, head shape and any legend plate or guard.
  • The mounting adapter, retaining hardware and permitted panel thickness.
  • The selected contact blocks and lighting module, where fitted.
  • The terminal or connector version and the direction in which its wires leave.
Exploded push button assembly with the operator head, mounting hardware and rear contact modules.

Terminal choice deserves a separate check. APEM’s panel-mount switch guide includes solder-lug, quick-connect and other terminal options across its switch families. Use the drawing for the version you will actually buy, with its mating connector or termination included.

Lay out the heads, holes and rear components together

Begin with the front view. Draw the outline of each button head, selector handle and identification plate around its hole center. Check the handle throughout its travel, and leave the operator room to press or turn the control without hitting its neighbor.

Then look behind the cover. Add the bodies, mounting nuts, contact blocks and connectors to the same layout. Two circular cutouts can sit neatly beside one another while the rear assemblies collide. A cover screw or molded corner boss also occupies space that a front-view drawing can miss.

Front and rear operator layouts showing potential interference inside a push button enclosure.

Use the component’s mounting drawing for the cutout diameter, tolerance and any locating notch. Check panel thickness against its clamping range, including any overlay that changes the mounting thickness. A nominal product description is not a machining drawing.

Section view showing a push button cutout, panel thickness and retaining hardware.

How far apart should the holes be?

Use the spacing requirements for your exact actuator and accessories. In its 22 mm push button technical data, Rockwell Automation specifically warns that 30 mm hole spacing does not work with certain knob-lever configurations.

For your drawing, confirm the front operating space, the rear component clearance and access for the retaining tool. If one needs a wider pitch, revise the layout before selecting a pre-drilled cover.

Selector switch layouts comparing handle movement and spacing between adjacent controls.

Check usable depth with the wiring attached

Measure from the inside mounting face of the cover to the nearest obstruction behind the operator. That obstruction might be the box floor, a mounting rail, a terminal strip or cable-entry hardware. The catalog’s external depth does not give you this measurement.

Section view comparing enclosure depth with the usable space behind an installed operator.

Place the complete rear assembly in the section view, including its connector. Next, draw where the wire goes after leaving the terminal. A connector pointing toward the floor needs space in that direction; a side-facing connection needs room beside the operator. Apply the cable manufacturer’s bend requirements to the actual cable.

Also check the actions needed during assembly. Can a screwdriver approach the terminal? Can you release a contact block or unplug a connector? A part can fit inside a box while leaving no practical way to service it.

Push button wiring layout showing cable routing space and access to rear terminals.

A compact operator can sometimes resolve the depth problem. In EAO’s published CereTom case study, the selected Series 84 emergency stop had a maximum back-of-panel depth of 18 mm. That dimension belongs to the device described in that case. For your assembly, compare the current drawings of suitable operators before committing to a deeper enclosure.

Put the cable entry on the layout now

Draw the complete gland or conduit fitting, including its internal locknut. Then check it against the nearest operator body, fixing point and wire route. A circle on the sidewall shows the opening; it does not show the fitting projecting into the box.

Mark the approach direction of the incoming cable as well. If the box mounts against a machine frame, check that the frame leaves room for the fitting, cable bend and installation tool.

Cable gland and internal locknut clearance beside a push button enclosure operator module.

Where devices mount on a removable or hinged cover, show what happens to the connected wires when it opens. Follow the harness through that movement: it must avoid the gasket and screw locations, and allow the cover to open without pulling on terminals. Check this with the intended cable and routing, not an empty box.

Enclosure cover movement illustrating the wiring slack needed for a service loop.

Choose standard holes when they fit the complete assembly

Keep a standard enclosure if its hole pattern, usable depth and entry positions work. Ask for custom machining when the body already fits and only the openings need to change. Consider a different body when the depth, mounting arrangement or available face area remains wrong.

RouteUse it whenConfirm before ordering
Standard pre-drilled enclosureThe supplied pattern matches the complete operator layoutExact hole pattern, device compatibility, rear clearance and entry options
Standard enclosure with custom openingsThe body fits, but the required holes, spacing or entry locations differDimensioned cutouts, machinable areas, orientation and approved drawing revision
Custom enclosure bodyAvailable bodies cannot accommodate the assembly or machine mountingBody geometry, cover construction, mounting details and the full interface drawing
Standard enclosure, custom-machined openings and custom enclosure body compared.

For a metal cover, check openings close to a formed edge with the fabricator. Protocase’s guidance on cutouts near bends explains how bending can stretch or flare a nearby opening. The necessary distance depends on material, thickness and tooling. Moving a hole toward the edge to gain button spacing can therefore create a manufacturing problem.

If the body needs to change, use a custom electrical enclosure brief that shows the mounting and internal arrangement as well as the front face.

What should you send for a quotation?

For a standard box, send the enclosure part number and operator list, then confirm the complete fit. For custom openings, add a dimensioned drawing that identifies the view, units and revision. Label the front view explicitly so an asymmetric pattern cannot be mistaken for a rear view.

Information to sendDetails that make the request usable
Supply scopeEmpty enclosure, machined enclosure, or an assembly with separately defined responsibilities
Operator listExact models, quantities, accessories and mounting drawings
Space and mounting limitsAvailable H × W × D, mounting points and space around the installed box
LayoutFront view, rear component arrangement and a section through the deepest assembly
Custom cutoutsHole sizes, locating features, center positions from a stated datum, tolerances, units and drawing revision
Cable entriesEntry side, fitting model or thread, cable diameter and intended routing
Enclosure requirementsMaterial, finish, installation environment and required protection rating for the finished configuration
Order requirementsQuantity, sample or first-article requirements, and requested delivery date

Agree on the drawing format the supplier can use. A CAD file can define geometry, while a dimensioned PDF records the tolerances and notes needed for approval. Make clear which revision controls manufacturing.

Enclosure quotation drawing package with operator layouts, section views and cable-entry details.

Prove a new layout before releasing the batch

For a crowded or unfamiliar assembly, check a sample with the selected hardware fitted. Install the operators and cable-entry fittings, connect a representative harness, then check cover closure and service access. Record any changes on the drawing before approving production.

Illustrative sample-fit check of a push button enclosure before batch production.

In Tri-Tech 3D’s APEM case study, APEM used a printed alignment jig to drill pushbutton holes into a molded part for a customer’s prototype. The case describes modifying the molding tool if the design proceeded to production.

For your project, agree how the hole positions and assembled fit will be checked before you commit to the batch. A finished sample should let the reviewer reach the terminals and remove the cover, not merely confirm that the buttons pass through the holes.

FAQ

Can I mix operators from different manufacturers?

Check each device against the enclosure drawing. Matching nominal hole sizes does not establish compatibility: cutout details, panel thickness, spacing and rear dimensions still need to match. Keep the manufacturer’s specified mounting and accessory combinations together unless an alternative is approved.

Should I add spare holes for future controls?

Only where you have also reserved rear space and a wiring route. Identify the future device size where possible and specify suitable blanking plugs for unused openings. Include those plugs in the finished enclosure’s protection requirements.

Can I send a sketch instead of a finished CAD drawing?

A marked-up sketch can start the quotation discussion. Include known dimensions and label anything still undecided. Before machining, agree on a dimensioned approval drawing with the supplier so hole positions, tolerances and orientation are fixed.

Send the layout with your enclosure request

Send FN Enclosure your operator list, mounting drawings, target dimensions and cable-entry positions. If a dimension or component is still undecided, mark it on the sketch so it stays visible during review.

Send your layout for an enclosure quotation.